Ford S-Max mk1
Audi TT mk1
Ford Mondeo Mk4
Octavia 1
Fabia 1
1 / 4
Škoda Octavia 1 · 2001–2010
Octavia 1 Bi-xenon sada
Bi-xenon conversion kit for the first generation Octavia from the original lighted xenon projectors to the much more powerful bi-xenon projectors, retaining the original light adjustment and auto-leveling.
- Úpravy světlometu
- žádné
- Výbojky
- původní D2S
- Montáž
- 1–2 h, otvorem pro výbojku
- Low beam / high beam
- 5,795 / 6,746 lx
While the headlights are off
For full output the lenses must be in good shape. Yellowed or scratched lenses scatter light and blur the sharp cut-off. While you are removing the headlights anyway, it pays to replace the covers at the same time.
We measure, not promise.
We compared a typically worn original projector with ours. Same bulb, same ballast, same camera settings.
Measured from 3.5 m
The kit also works as a high beam. You can keep the original halogen bulbs connected; then both sources shine.
Even complete beginners can do it
The front lenses stay sealed. Everything is done through the bulb opening. Not counting removing and refitting the headlights, it takes one to two hours.
9 steps · 18 photos
Fitting guide · Octavia 1Retrofit of Bi-xenon headlights
Removing the rear headlight coverOdšroubujte pět šroubů na zadní části světlometů pomocí torx t20.
Removal of the projectorRemove the two nuts and the Torx screw holding the projector in place.
WiringMake sure that the wiring from the package is connected to the projector.
Every step with a photo, from tools to the finished light.Open the guide
An electrically controlled shield gives you two beams.
The reflector focuses the bulb's light to the lens's focal point. That is where the shield sits. The lens projects a sharp cut-off onto the road.
Low beam
The shield absorbs the lower half of the rays heading into the lens. The lens flips the image so light shines only below the cut-off. The result is a sharp cut-off that rises to the right towards the roadside. As a result, oncoming drivers are not dazzled.
High beam
A solenoid folds the shield down and all the rays pass through the lens. The cut-off disappears and the light shines like the low beam, plus far ahead of the car. The original halogen high beams shine at the same time.
5,795 lx
low beam, our kit
6,746 lx
high beam, our kit
Why original projectors barely shine after years
Inside the original projector, a reflector has a thin chrome layer. Over the years, heat and UV from the bulb burn it off. The surface turns dull or black and light has nothing to bounce off. The bulb shines, but only a fraction of its light reaches the road.
A burnt original projector next to a new one from our kit. Drag the slider.
A reflector that lasts much longer
The reflector is made from aluminum. It dissipates heat better, so the chrome lasts much longer than the original, and the reflector doesn't warp. Light bounces off the whole surface, not just what is left of it.
Geometry like modern cars
The reflector, shield and lens follow modern projector design, not the technology from when the car left the factory. More light from the bulb reaches the lens and is then projected onto the road.
Sharp cut-off, clear lens
The shield is laser-cut, so the cut-off is sharp and oncoming drivers are not dazzled. The crystal-clear lens lets through maximum light and leaves the typical blue edge.
How it shines on the road at night
Photos from our night drives with this kit. No edits, same camera settings.
Everything in one box
- 2×bi-xenonový projektor
- 2×adaptér pro Octavii 1
- 2×clonka pro usměrnění světla
- 2×držák výbojky
- 1×kabely k elektromagnetům clony
- 1×spojovací materiál a samořezné spojky na dálková
Bulbs are not included, but the original D2S fits the projector.
Before you order
Only for original xenon headlights
The kit is for original Octavia 1 xenon headlights. Have aftermarket Depo headlights? Write to us before you order.
Lenses must be in good condition
Cracked or yellowed lenses disrupt the cut-off, cause glare, and reduce output. We have new headlight covers for this car.
You already have the bulbs
The projectors take the same bulb base as your original headlights, so you reuse the bulbs you have. New bulbs are brighter, but originals in good condition are fine.
Road use
The kit is not intended for use on public roads.
Frequently asked questions
Did not find your answer? Write to us.
Jak poznám, že mám originální xenon?
Nejjistější je poslat nám fotku světlometu zezadu. Podle ní vám potvrdíme, jestli sada pasuje.
Zvládnu montáž sám?
Ano. Skla se nerozlepují, všechno jde otvorem pro výbojku. Ke každé sadě je návod, a když se zaseknete, pomůžeme.
Zůstane mi automatická nivelace?
Ano. Původní seřizování i automatická nivelace světel zůstanou zachované.
Co dálková světla?
Přibude vám zdroj na dálková, naměřili jsme 6 746 lx. Původní halogenová dálková si můžete nechat.
Můžu použít LED výbojky?
Ano, pokud mají patici D2S.
Full kit description
Our retrofit kit for Škoda Octavia 1 (2001-2010) contains everything you need to replace the original xenon projectors (xenon only illuminates the low beam) to a much more powerful bi-xenon projectors (xenon lights for low beam and high beam) with keeping the original adjustment and automatic levelling of the lights.
The main advantages of our bi-xenon projectors
- Multiply stronger light output
- A high beam source will be added, the original high beams may or may not be retained. It's up to you.
- Projectors are unlike the original made from aluminiumso that it won't warp or burn even after years. At the same time, they also help to better dissipate heat, which makes the projector chrome has a longer life than the original lights.
- The projector's aperture is laser cut to achieve the most accurate light refraction. At the same time, it does not let any light above the refraction, so it does not glare on oncoming vehicles.
- Projectors have crystal clear lenswhich is used for maximum brightness and leaves a blue coloured refraction.
This is a simple conversion that even complete beginners can handle. There is no need to unstick the front Plexiglas for the lights. Everything can be done through the hole to change the lamp and, if you ignore the dismantling and fitting of the headlights, you can expect the job to take between one and two hours.
The kit is assembled to be completely Plug & Play, which means that there is no need to modify anything for the installation. We also create for each car video tutorial, which will completely guide you through the installation, or we can help you with the installation via phone, email or social media.
The set includes two bi-xenon projectors, cables from the aperture electromagnets, lamp holders, two adapters for Octavia 1, two apertures to direct the light, all necessary fasteners for installation, self-cutting connectors for connection to the original driving lights.
The projector fits the original D2S xenon lamps, so there is no need to purchase new ones for the conversion. LEDs with D2S socket can also be used.
To ensure perfect luminosity it is necessary that the plexiglass is in good condition. Cracked or yellowed Plexiglas interferes with the refraction of light, which can cause glare from oncoming vehicles and also significantly reduces luminosity. We have Plexiglas for Octavia 1 here.
The set is not intended for use on public roads.
The kit is made for OEM Xenon headlights. For use in Depo aftermarket lights, please contact us.
We also have a detailed installation instructions.
Čeština 
English (UK)